View and Download Canon ImagePROGRAF iPF Series service manual online. ImagePROGRAF iPF Series Printer pdf manual download. View and Download Canon ImagePROGRAF iPF brochure & specs online. Large-Format Printer. ImagePROGRAF iPF Printer pdf manual download. and free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Canon IPF Printer User Manual. Page 1. Page 2.
|Published (Last):||5 August 2006|
|PDF File Size:||18.23 Mb|
|ePub File Size:||5.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
F 9 Set the printhead. Main Menu Chapter 1 1. Yes” is selected in the printer driver when roll media is used, the cutter unit mounted in front of the spur unit automatically cuts the roll media. Ink Tank Unit Chapter 4 F 6 Disconnect the two waste ink tubes, and then remove the platen duct by removing the five screws and five bushings. Ink tank cover switch The micro-switch-type ink tank cover switch detects opening and closing of the ink tank cover. F – Never touch the ink port and contacts.
Introduction Symbols Used This documentation uses the following symbols to indicate special information: It is detected according to the voltage changes at the two terminals of the contact faces, power supply terminals, and GND terminal. Page Chapter 5 – Do not dry the interiors of the top cover with a dry cloth. Page Chapter 3 b. Page 71 Chapter 1 6. Series B plug compliant with USB standard b. Page Chapter 3 F 13 Holding the knobs,take out the printhead from the case. Chapter 2 Semi-glossy canvas 0.
Page Contents Contents 8. Purge Unit Chapter 2 2. Chapter 2 of higher color calibration accuracy.
When the auto roll feed unit is not mounted, the printer starts manuall the media when the paper detection sensor detects the media.
Product Specifications Chapter 1 1. Page Chapter 3 F 9 With Basket Wire 2  positioned so that the bend faces forward, insert it in the hole of the Basket Table  from below. To move the carriage whth the power off, you need to release the carriage lock pin and cap manually.
Chapter 2 cutter cutter lift motor cutter right cutter motor position sensor cutter lift sensor cutter HP sensor F 2. Service Mode Operation Chapter 7 7. Chapter 2 Spur cam sensor Cassette cam sensor Paper detection sensor Cassette pick-up sensor Cassette encoder sensor Cutter lift sensor Cutter HP sensor Cutter right position sensor F Cassette pick-up sensor This is janual photo-interrupter-type sensor. Indicates an item requiring care to avoid electric shocks.
Page 81 Chapter 1 Page Chapter 2 Holding plate lifter lever Holding plate lifter lever Cassette cam sensor F The excess sheets separated by the separation roller are returned to the cassette using the sheet return guide. Canon could take a lesson from Epson lpf5000 HP on delivering clear user documentation for their products.
To prevent this, the feed error encoder and feed roller HP sensor detect the presence and amount of feed roller eccentricity every rotation of the feed roller. F – Never touch the ink port and contacts. Chapter 2 Pump encoder sensor The pump encoder is a photo-interruptive type sensor.
The time until the printer enters the Sleep mode can be changed from the operation manuak. Once in place, plug the Canon iPF in and you’ll be prompted to install the two print heads, followed by the 12 ink cartridges. Page 67 [Advanced Adj. Chapter 4 F 3 Remove the three screws, remove the waste ink tube joint by turning it in the direction of the arrow, and then remove the purge unit. Introduction Ipf500 following rules apply throughout this Service Manual: Chapter 4 F c Left cover Removing the left cover 1 When removing the left cover, remove the left circle mabual, open the top cover, and then remove the tank cover.
Basic Operation Chapter 1 1. Head Management Sensor Chapter 4 F 9 Remove the four screws and one joint, and then remove the two ink tank unit F. Precautions for Troubleshooting 1 Check the environmental conditions and the media used ippf5000 printing. This printer features a mechanism by which mmanual the correct color ink tank will fit in the given slot.
Insert it as far as it will go while taking care that the nozzles and contacts do not touch the carriage. F – Never touch the ink port  and contacts .
Canon IPF5000 Printer User Manual
The output stacker included with stand can use by the two ways of the regular position or extended position. Also an option, and one that I have for my printer is the roll feed unit.
Page Chapter 4 F f Removing the spur unit 1 When removing the spur unit, first open the top cover, and then remove the left and right circle covers, tank cover, right upper cover, operation panel, lower rear cover, right cover, right front cover, upper front cover, lower front cover, cover guide, upper rear cover, and left and right cover mounting plates.
Main Controller Chapter 2 2. When media is fed from the auto roll feed unit by the specified length, the nulti sensor performs the adjustments and detection shown below, thus completing the roll media pick-up operation.
Page Chapter 5 Keep the bag in a safe place, because it is used for cleaning sheet. The received data is not suitable for borderless printing.
F mqnual Procedure after replacing the head management sensor Since the distance between the head management sensor and the carriage unit varies among printers, the optical axis is factory-adjusted to adjust the non-discharging detection position. Roll Media Pick-up Sequence Chapter 2 roll cam sensor roll feed unit PCB roll manuap F If the roll media sensor detects that there is no roll during roll media pick-up operation, the roll media is ejected.
To arrange for warranty services by Canon please call: Page Chapter 4 F c Left cover Removing the left cover 1 When removing the left cover, remove the left circle cover, open the top cover, and then remove the tank cover.