ASTM C128 PDF

Referenced Documents. ASTM Standards: C 29/C 29M Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate2. C 70 Test Method for Surface. ASTM Designation: C 1. SCOPE. This method covers the determination of bulk and apparent specific gravity, 23/23ºC. (/ºF), and absorption. Qty. Model, Description. 1, Choose One: HBA, Adam Core balance g x g, V 60Hz. HBA.4F, Adam Core balance g x g, V 50/.

Author: Bakus Kagagrel
Country: Lebanon
Language: English (Spanish)
Genre: Literature
Published (Last): 17 September 2012
Pages: 451
PDF File Size: 10.13 Mb
ePub File Size: 19.82 Mb
ISBN: 135-8-41967-265-5
Downloads: 71969
Price: Free* [*Free Regsitration Required]
Uploader: Bajas

The OD relative density is determined after drying the aggregate. Conversely, some aggregates that have not been continuously maintained in a moist condition until used are likely to contain an amount of absorbed moisture less than the h soaked condition.

The relative density specific gravitya dimensionless quality, is expressed as oven-dry ODsaturated-surface-dry SSDor as apparent relative density specific gravity. axtm

For an aggregate that has been in contact with water and that has free moisture on the particle surfaces, the percentage of free moisture is determined by deducting the absorption from the total moisture content determined by Test Method C by drying. Likewise, relative density specific gravitya dimensionless quality, is expressed as OD, SSD, or as apparent relative density apparent specific gravity. Link to Active This link will always route to the current Active version of the standard.

These notes and footnotes excluding those in tables and figures shall not be considered as requirements of this test method. No other units of measurement are included in this standard.

  BUTTERFIELD WHIG INTERPRETATION OF HISTORY PDF

ASTM C Standard

The laboratory standard for absorption is that obtained after submerging dry aggregate for a prescribed period of time. Aggregates mined from below the water table commonly have a moisture content greater than the absorption determined by this test method, if used without opportunity to dry prior aatm use.

Work Item s – proposed revisions of this standard. Relative density specific gravity SSD is used if the aggregate is in a saturated surface-dry condition, that is, if its absorption has been satisfied.

The test results for density shall be reported in either SI units or inch-pound units, as appropriate for the use to be made of the results. Link to Active This link will always route to the current Active version of the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Active view current version of standard. Axtm density specific gravity SSD is used in the determination of surface moisture on fine aggregate by displacement of water in Test Method C Referenced Documents purchase separately The documents listed astk are referenced within the subject standard but are not provided as part of the standard.

The OD density and Asrm relative density are determined after drying the aggregate. The SSD density, SSD relative density, and absorption are determined after soaking the aggregate in water for a prescribed duration. The values obtained for absorption by other test methods will be different than the values obtained by the prescribed h soak, as will the relative density specific gravity SSD.

  KATSUYA HOSOTANI PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as c1228 of the standard. This value is not widely used in construction aggregate technology. Alternatively, the relative density specific gravity OD is used for computations when the aggregate is dry or assumed to be dry.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The SSD relative density and absorption are determined after soaking the aggregate in water for a prescribed duration.

Active Risk Management

Historical Version s – view previous versions of standard. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of this test method. It is also expressed as the ratio of the density astmm the aggregate particles to the density of water. Work Item s – proposed revisions of this standard.